| ||
| ||
|
Martial Arts Information | |
|
|
Interesting Facts on Samurai Sword Manufacture
A samurai's sword is his most sacred and prized possession. Not only did the samurai rely on his sword to defend him, but spiritually the sword held greater significance as the samurai actually believed his soul inhabited the sword. Therefore it comes as no surprise that the same discipline and respect in which the samurai wielded his sword, went into the actual making of the sword itself. Swords weren't simply 'cast' in a mould and then sharpened. A Japanese samurai sword was made by an intricate process of heating the steel, hammering it flat, then folding it, then hammering it flat again, and folding. This process of repeated hammering and folding would be done up to as much as 30 times, or until the maker was satisfied it had been done properly. There are quite a few reasons for this labour-intense procedure. Firstly, any air pockets which might develop during the heating of the steel would be eliminated. Having an air pocket in a seemingly solid blade would be a weak point, and any weak point would be seen as neglect and any dedicated artisan would produce the highest quality blades as if his own life depended upon the very blade he was forging. Secondly, in the repeated folding and hammering, what might be described as 'layers' were produced. Take a book and roll it up it parallel with the spine, these internal layers would look something like this, almost like the rings of a cross section of a tree trunk. This added much strength to the blade. Also the natural strengthening carbon elements within the steel, as well as the steels impurities would be spread throughout the whole of the sword, therefore strengthening it in its entirety. When the blade came to be cooled it wasn't simply quenched in water, another process had to be done first. When steel is been cooled, if it cools from a high temperature right down to cold in a short amount of time, the metal becomes very hard and brittle. Conversely, if steel is cooled slowly from a lower temperature right down to cold, the steel takes on more supple, even softer properties. Because a samurai sword was used primarily as a slicing weapon the blades were subjected to a lot of shock upon impact on the enemy, therefore the blade couldn't be made of the more brittle steel throughout else it would shatter like glass. But the sword had to retain its sharp edge, so it couldn't be made of softly forged steel throughout else it would simply blunt. So a balance was struck using a very clever procedure. What the Japanese samurai sword makers discovered was by painting on a clay formula onto the blade before quenching, thin amounts onto the cutting edge and thicker amounts onto the back, the steel could be made to take on two completely separate properties, thereby giving the blade the hard cutting edge it required, and the more supple back. Because of the different speeds in which the two halves of the steel cooled this also formed the beginning of the curve from which the sword makers would work to create the famous curved blade. Article by Nick Johnson, visit his website for more on samurai swordshttp://www.japanese-samurai-swords.net
MORE RESOURCES:
Martial-Arts - Google News |
|
|
|
RELATED ARTICLES
Learning the Modern Dynamics of Judo You may have the erroneous idea that force is not necessary in judo, especially when you see a sixty-year-old instructor throwing many young- and strong men seemingly without effort. Dynamics, however, denies this illusion. Samurai Armor Part 1 The first prototype for Japanese samurai armor came about in the form of the yoroi during the Gempei War of 1181-1185. The weight of the yoroi was around 60lb. Samurai Swords and The Swordsmiths Back in the early times of sword manufacture, the production of super strong high-grade carbon steel wasn't even a vague dream. But we know, as history has taught us, that sword makers of ancient times still managed to produce superb quality, strong weapons. John Styers Most people have only been exposed to John Styers work through the book "Cold Steel".It is important to remember that first and foremost this book outlines a BASIC course of close-combat instruction. Fronting "Fronting": The dodge to get in close to you. The frontal assault, as opposed to the ambush. Nuts & Bolts of Self Defense Fundamental "Nuts & Bolts" training for close combat should be directed at dealing with the extremes. That is a life and death struggle for survival, i. By-Rote Combinations Do not believe that practicing "by rote" 1-2-3,etc. type "responses" to street attacks is a viable or particularly useful training exercise. The Plight of Industrialized Man Living in the Pacific Northwest is a challenge for any body: the poor excuse for weather west of the Cascades is one of the worst on earth for human health. Luckily our Ch'uan Fa Club meets in central Oregon several times a week, rarely missing an opportunity to train outdoors . Martial Training as a Timeless Portal Thanks to several centuries of enlightened teachings by extraordinary men in the martial disciplines, we don't have to be restricted to lives of getting and spending, waiting in quiet desperation for the pain to cease.Most of us in the Arts focus on the tasks in front of our noses (the correct hand forms/kicks/body alignments), forgetting our option to consciously evolve along the way to physical perfection. What To Expect When You Least Expect It The time you will be attacked you will most likely be:DistractedOut numberedAloneThere will be no back upYou will be in the fight of your life.Specific Defenses don't work. Applying Law of Gravity to Judo In judo it is important to throw your opponent by making use of his loss of balance, the law at work here is the law of gravity. We know that Sir Isaac Newton discovered the law of gravitation by seeing an apple fall from a tree. I Know Karate and Kung Fu and Lots of Other Foreign Words! Martial arts have become incredibly popular in the US. Drive through any little strip shopping center in nearly any city and you're likely to see a martial arts studio. The Fallacy and the Myth It's always amusing when "know it alls" dismiss certain methods out of hand as being useless or "unworkable". One "victim" of this line of thinking is the "cross arm" or "X" block (for lack of a better term). Samurai Sword Facts The first samurai swords we're actually straight bladed, single edged weapons imported from Korea and China known as chokuto, which were later replaced with the curved blade variety at the end of the 8th Century. The name of the curved blade swords which replaced them was Tachi. Real Life Self-Defense Starts From... "Nicky Bats" was an "old school" kinda guy. He was "street" thru and thru. Combatives This is our last installment on "defining" the parameters of COMBATIVES.The point, I am sure, will be missed by some but it must be emphasized that this material is historical fact and is accurate in substance and detail. Judo Nagewaza (Throwing Technique) In The Street How practical are throwing techniques (nagewaza) for self-defense or street-fighting? NOT VERY!The Japanese themselves have a saying, "One year for newaza (ground technique), TEN YEARS for nagewaza (Throwing technique)". It takes ten times as long to become proficient at throwing than it does at ground fighting. The Dojo Just as an aside. For those who would "box" us in to specific "category". Bogu Training About four years ago Carl recommended we start using the Bogu during our kumite (sparring practice). This method was developed in Okinawa and then found its way into mainland Japan and eventually to the U. A Great Question! It's a question that we went back and forth with for awhile ourselves many moons ago. The "how" and "why" of our conclusions may be of some interest.
|
| home | site map |
| © 2006 |
